CURRENT NEWS                                                                              

LED device for capturing your signature in lights

Aug 12, 2013
A new sensor incorporating GaN (gallium nitride) could provide an artificial sense of touch and be used in biological imaging and MEMS systems

Researchers at the Georgia Institute of Technology have developed a sensor  that converts mechanical pressure - from a signature or a fingerprint - directly into light signals that can be captured and processed optically.

The scientists used  thousands of zinc oxide (ZnO) nanometre-scale wires to accomplish this,

The sensor device could provide an artificial sense of touch, offering sensitivity comparable to that of the human skin. Beyond collecting signatures and fingerprints, the technique could also be used in biological imaging and micro-electromechanical (MEMS) systems.

And ultimately, it could provide a new approach for human-machine interfaces.

"You can write with your pen and the sensor will optically detect what you write at high resolution and with a very fast response rate," says Zhong Lin Wang, Regents' professor and Hightower Chair in the School of Materials Science and Engineering at Georgia Tech. "This is a new principle for imaging force that uses parallel detection and avoids many of the complications of existing pressure sensors."



Zhong Lin Wang holding the sensor device along with his research team in the background

Individual ZnO nanowires that are part of the device operate as tiny LEDS when placed under strain from the mechanical pressure. They allow the device to provide detailed information about the amount of pressure being applied.

Known as piezo-phototronics, the technology - described by Wang in 2009 - provides a new way to capture information about pressure applied at very high resolution: up to 6,300 dots per inch.

Piezoelectric materials generate a charge polarisation when they are placed under strain. The piezo-phototronic devices rely on that physical principle to tune and control the charge transport and recombination by the polarisation charges present at the ends of individual nanowires.

Grown on top of a GaN film, the nanowires create pixelled light emitters whose output varies with the pressure, creating an electroluminescent signal that can be integrated with on-chip photonics for data transmission, processing and recording.

"When you have a zinc oxide nanowire under strain, you create a piezoelectric charge at both ends which forms a piezoelectric potential," Wang explains. "The presence of the potential distorts the band structure in the wire, causing electrons to remain in the p-n junction longer and enhancing the efficiency of the LED."

The efficiency increase in the LED is proportional to the strain created.

Differences in the amount of strain applied translate to differences in light emitted from the root where the nanowires contact the GaN film.

To fabricate the devices, a low-temperature chemical growth technique is used to create a patterned array of ZnO nanowires on a GaN thin film substrate with the c-axis pointing upward.

The interfaces between the nanowires and the GaN film form the bottom surfaces of the nanowires. After infiltrating the space between nanowires with a PMMA thermoplastic, oxygen plasma is used to etch away the PMMA enough to expose the tops of the zinc oxide nanowires.

A nickel-gold electrode is then used to form ohmic contact with the bottom gallium-nitride film, and a transparent indium-tin oxide (ITO) film is deposited on the top of the array to serve as a common electrode.

When pressure is applied to the device through handwriting, nanowires are compressed along their axial directions, creating a negative piezo-potential, while uncompressed nanowires have no potential.



Schematic showing a device for imaging pressure distribution by the piezo-phototronic effect. The illustration shows a nanowire-LED based pressure sensor array before (a) and after (b) applying a compressive strain. A convex character pattern, such as "ABC," molded on a sapphire substrate, is used to apply the pressure pattern on the top of the indium-tin oxide (ITO) electrode.

The researchers have pressed letters into the top of the device, which produces a corresponding light output from the bottom of the device. This output - which can all be read at the same time - can be processed and transmitted.

The ability to see all of the emitters simultaneously allows the device to provide a quick response. "The response time is fast, and you can read a million pixels in a microsecond," says Wang. "When the light emission is created, it can be detected immediately with the optical fibre."

The nanowires stop emitting light when the pressure is relieved. Switching from one mode to the other takes 90 milliseconds or less, Wang says.

The researchers studied the stability and reproducibility of the sensor array by examining the light emitting intensity of the individual pixels under strain for 25 repetitive on-off cycles. They found that the output fluctuation was approximately 5 percent, much smaller than the overall level of the signal. The robustness of more than 20,000 pixels was studied.

A spatial resolution of 2.7 µm was recorded from the device samples tested so far. Wang believes the resolution could be improved by reducing the diameter of the nanowires - allowing more nanowires to be grown - and by using a high-temperature fabrication process.

The researchers' study is described in detail in the paper, "High-resolution electroluminescent imaging of pressure distribution using a piezoelectric nanowire LED array," by Caofeng Pan et al in Nature Photonics (2013), published online on 11th August 2013.   DOI:10.1038/nphoton.2013.191

This research was sponsored by the U.S. Department of Energy's Office of Basic Energy Sciences, the National Science Foundation, and the Knowledge Innovation Program of the Chinese Academy of Sciences.

 
NEWS
Compound Semiconductor. The most respected, authoritative and widely read information source connecting the community since 1995 To view the latest issue of Compound Semiconductor, click here
To register free of charge to receive news via e mail on a weekly basis click here.
Search the Compound Semiconductor web site
 
Submit your Lab & Fab article
It is imperative that CompoundSemiconductor.net remains a timely resource for this industry, so we are only interested in highlighting very recent work reported in academic papers.  Therefore, please only consider writing a short piece highlighting your work if you have a journal paper that has been accepted and about to appear in press, or a paper that has been published within the last month. For further guidelines, click here.
SHARE THIS
    Email this article to a friend
  Connotea       Cite-U-Like        Del.icio.us        Digg       

                                  

                           
 
FREE SUBSCRIPTION
CORPORATE PARTNERS






























































For maximum exposure, become a Corporate Partner.
Contact our sales team.
Buyer's Guide